机械加工中有限元技术的计算精度优化研究

doi:10.16180/j.cnki.issn1007-7820.2024.03.013

Abstract

Abstract:

Finite element model technology is widely used in the field of machining, it is also the core theory technology to realize digital control and modern machining, and has been widely concerned and deeply discussed by researchers in various fields. The calculation and simulation technology based on the finite element model can greatly improve the precision of machining and manufacturing, and a large number of machined parts experiments also provide detailed data and reference for the finite element model.This study summarizes the research history of finite element analysis technology, analyzes and summarizes the core strategy of precision optimization in the current finite element analysis technology and its shortcomings, and looks forward to the future development direction of finite element analysis technology in the machining process.

Key words: machining, finite element simulation, calculation accuracy, residual stress, error function, numerical analysis, orthogonal cutting, workpiece lifespan

CLC Number:

TP391

YANG Yunhui. Research on Optimization of Calculation Accuracy of Finite Element Technology in Mechanical Processing[J].Electronic Science and Technology, 2024, 37(3): 98-102.

References 40

[1]	Strebjiwsjum H S, Canoll III J T. A finite element model of orthogonal metal cutting[J]. Journal of Engineering for Industry, 1985, 107(2):349-354. doi: 10.1115/1.3186008
[2]	Komvopoulos K, Erpenbeck S A. Finite element modeling of orthogonal metal cutting[J]. Journal of Engineering for Industry, 1991, 113(1):253-267. doi: 10.1115/1.2899695
[3]	Wiesner C. Residual stresses after orthogonal machining of AlSl 304:Numerical calculation of the thermal component and comparison with experimental results[J]. Metallurgical Transactions A, 1992, 23(3):989-996. doi: 10.1007/BF02675573
[4]	Shih A J. Finite element simulation of orthogonal metal cutting[J]. Journal of Engineering for Industry, 1995, 117(1):84-93. doi: 10.1115/1.2803283
[5]	Wern H. Finite-element solutions for mechanical drilling methods:A new integral formalism[J]. Journal of Computational and Applied Mathematics, 1995, 63(1-3):365-372. doi: 10.1016/0377-0427(95)00089-5
[6]	Yang G, Tite C, Smith G T, et al. Determination of residual stresses induced by hardened steel turning using finite element methods[C]. Boston: Design Engineering Technical Conferences collocated with the ASME, 1995:356-363.
[7]	Lin Z, Lee L. An investigation of the residual stress of a machined workpiece considering tool flank wear[J]. Journal of Materials Processing Technology, 1995, 51(1-4):1-24. doi: 10.1016/0924-0136(94)01322-R
[8]	Chou I A, Chan H M, Harmer M P. Machining-induced surface residual stress behavior in Al₂O₃-SiC nanocomposites[J]. Journal of the American Ceramic Society, 1996, 79(9):2403-2409. doi: 10.1111/jace.1996.79.issue-9
[9]	Lin Z C, Lai W L, Lin H Y, et al. Residual stresses with different tool flank wear lengths in the ultra-precision machining of Ni P alloys[J]. Journal of Materials Processing Technology, 1997, 65(1-3):116-126. doi: 10.1016/0924-0136(95)02251-1
[10]	Abdel-Rahman N, Sivakumaran K S. Material properties models for analysis of cold-formed steel members[J]. Journal of Structural Engineering, 1997, 123(9):1135-1143. doi: 10.1061/(ASCE)0733-9445(1997)123:9(1135)
[11]	Lee D, Kim J K. Measurement of residual stresses in encapsulant of a PQFP[C]. Chicago: Proceedings of the Second Electronics Packaging Technology Conference,IEEE, 1998:236-240.
[12]	Fraser S, Attia M H, Osman M. Modelling,identification and control of thermal deformation of machine tool structures,part 1:Concept of generalized modelling[J]. Journal of Manufacturing Science and Engineering, 1998, 120(3):623-631. doi: 10.1115/1.2830167
[13]	Jacobus J K, Devor R E, Kapoor S G. Part warpage model based on machining-induced residual stress[J]. Technical Paper Society of Manufacturing Engineers, 1999, 39(8):1-6.
[14]	Perl M. The change in overstrain level resulting from machining of an autofrettaged thick-walled cylinder[C]. Dallas: ASME Pressure Vessels and Piping Conference, 1999:621-628.
[15]	El-Wardany T I, Kishawy H A, Elbestawi M A. Surface integrity of die material in high speed hard machining,part 2:Microhardness variations and residual stresses[J]. Journal of Manufacturing Science & Engineering, 2000, 122(4):620-631.
[16]	Tanner D A, Robinson J S, Cudd R L. Cold compression residual stress reduction in aluminium alloy 7010[J]. IEEE Transactions on Machinal Technology Review, 2000(7):235-240.
[17]	Yang X, Liu C R. A new stress based model of friction behaviour in machining and its significant impact on residual stresses[J]. International Journal of Mechanical Sciences, 2002, 44(4):703-723. doi: 10.1016/S0020-7403(02)00008-5
[18]	Dattoma V. On the evolution of welding residual stress after milling and cutting machining[J]. Computers & Structures, 2006, 84(29-30):1965-1976. doi: 10.1016/j.compstruc.2006.08.008
[19]	Shih A J, Yang H. Experimental and finite element predictions of residual stresses due to orthogonal metal cutting[J]. International Journal for Numerical Methods in Engineering, 2010, 36(9):1487-1507. doi: 10.1002/nme.v36:9
[20]	Arrazola P J, Kortabarria A, Madariaga A, et al. On the machining induced residual stresses in IN718 nickel-based alloy:Experiments and predictions with finite element simulation[J]. Simulation Modelling Practice & Theory, 2014, 41(1):87-103.
[21]	Huang X, Jie S, Li J. Effect of initial residual stress and machining-induced residual stress on the deformation of aluminium alloy plate[J]. Strojniski Vestnik Journal of Mechanical Engineering, 2015, 61(2):131-139.
[22]	Pan Z, Liang S Y, Garmestani H. Finite element simulation of residual stress in machining of Ti₆Al₄V with a microstructural consideration:[J]. Journal of Engineering Manufacture, 2019, 233(4):1103-1111. doi: 10.1177/0954405418769927
[23]	Wang B, Yan C, Li J, et al. Residual stress and deformation analysis in machining split straight bevel gears[J]. Journal of Mechanical Engineering, 2021, 67(3):1-9.
[24]	Zhuang K, Zhou S, Zou L, et al. Numerical investigation of sequential cuts residual stress considering tool edge radius in machining of AISI 304 stainless steel[J]. International Journal of the Federation of European Simulation Societies, 2022, 118(1):1-15.
[25]	Obikawa T, Usui E. Computational machining of titanium alloy-finite element modeling and a few results[J]. Journal of Manufacturing Science & Engineering, 1996, 118(2):208-215.
[26]	Cao Y Q. Failure analysis of exit edges in ceramic machining using finite element analysis[J]. Engineering Failure Analysis, 2001, 8(4):325-338. doi: 10.1016/S1350-6307(00)00024-8
[27]	Dirikolu M H, Childs T, Maekawa K. Finite element simulation of chip flow in metal machining[J]. International Journal of Mechanical Sciences, 2001, 43(11):2699-2713. doi: 10.1016/S0020-7403(01)00047-9
[28]	Das S, Klotz M, Klocke F. EDM simulation:Finite element-based calculation of deformation, microstructure and residual stresses[J]. Journal of Materials Processing Technology, 2003, 142(2):434-451. doi: 10.1016/S0924-0136(03)00624-1
[29]	Ning H, Wang Z, Jiang C, et al. Finite element method analysis and control stratagem for machining deformation of thin-walled components[J]. Journal of Materials Processing Technology, 2003, 139(1-3):332-336. doi: 10.1016/S0924-0136(03)00550-8
[30]	Zel T. The influence of friction models on finite element simulations of machining[J]. International Journal of Machine Tools & Manufacture, 2006, 46(5):518-530. doi: 10.1016/j.ijmachtools.2005.07.001
[31]	Bi Y B, Ke Y L, Cheng Q L, et al. Key technologies of physics-based milling process simulation[J]. Journal of Zhejiang University(Engineering Science), 2007, 41(4): 541-546.
[32]	Shetty R, Pai R, Rao S S. Finite element modeling of stress distribution in the cutting path in machining of discontinuously reinforced aluminium composites[J]. Journal of Engineering & Applied Sciences, 2008(6):6-18.
[33]	Pedro J Aa, Tugrul Z B. Investigations on the effects of friction modeling in finite element simulation of machining[J]. International Journal of Mechanical Sciences, 2010, 52(1):31-42. doi: 10.1016/j.ijmecsci.2009.10.001
[34]	Ozel T, Llanos I, Soriano J, et al. 3D finite element modelling of chip formation process for machining inconel 718:Comparison of fe software predictions[J]. Machining Science and Technology, 2011, 15(1):21-46. doi: 10.1080/10910344.2011.557950
[35]	Banerjee N, Sharma A. Development of a friction model and its application in finite element analysis of minimum quantity lubrication machining of Ti₆Al₄V[J]. Journal of Materials Processing Technology, 2016, 23(12):181-194.
[36]	Pashaki P V, Pouya M, Maleki V A. High-speed cryogenic machining of the carbon nanotube reinforced nanocomposites: Finite element analysis and simulation[J]. Journal of Mechanical Engineering Science, 2018, 232(11):1927-1936.
[37]	Yang L. Design and analysis of machining quality control system based on finite element technology[C]. Chongqing: IEEE International Conference on Power,Intelligent Computing and Systems,IEEE, 2020:809-816.
[38]	Dodla S, Idnani K, Katyal A. Finite element machining simulations of aerospace materials[J]. Materials Today:Proceedings, 2021, 46(9):991-998. doi: 10.1016/j.matpr.2021.01.136
[39]	Ranjan P, Hiremath S S. Finite element simulation and experimental validation of machining martensitic stainless steel using multi-layered coated carbide tools for industry-relevant outcomes[J]. Simulation Modelling Practice and Theory, 2022, 114(1):1-13.
[40]	Zhang Z, Feng S, Ding Y, et al. Thermal error modeling of spindle and dynamic machining accuracy reliability analysis of CNC machine tools based on IA and LHSMC[J]. Maintenance and Reliability, 2022, 24(1):100-113. doi: 10.17531/ein.2022.1.12

Research on Optimization of Calculation Accuracy of Finite Element Technology in Mechanical Processing

RichHTML

PDF (PC)

Like

Knowledge

Abstract

Cite this article

share this article

References 40

Related Articles 8

Metrics

Comments

Recommended 0

[1]	Cunsheng YU,Hongbing YAO,Limin HUANG,Xiajun YANG,Wanyu LÜ. Optical Design of Reflective ADB Module [J]. Electronic Science and Technology, 2022, 35(4): 47-52.
[2]	YANG Yunhui,XU Lianjiang. Summary of Finite Element Analysis Technology for High Precision Machining [J]. Electronic Science and Technology, 2022, 35(11): 98-103.
[3]	TIAN Yuanbo,LIU Guili,KONG Quancun. Design of Pulse Power Supply for Micro ECM Based on Interface Acidification [J]. Electronic Science and Technology, 2021, 34(8): 37-42.
[4]	CHENG Huaxiang,CHEN Jie,ZHANG Chi. Optimal Design of 6-bar Parallel Machine Tool Based on HyperWorks [J]. Electronic Science and Technology, 2020, 33(9): 25-30.
[5]	CHEN Zhongan1, GAO Zongshan1, ZHAO Yujin2,3, JIN Xuesong433. Measurement of Radial Residual Stresses in Spot Welds by the Hole-drilling DMI Strain Gage Method [J]. , 2016, 29(9): 18-.
[6]	YANG Fanghong,WU Zhiming,LU Longlong. Applications of Symmetric Turntable in Microwave Process [J]. , 2013, 26(6): 16-.
[7]	ZHAO Xi-Wei, REN Bin. Acoustic Emission Signal Noise Reduction Based on the Wavelet Theory [J]. , 2013, 26(4): 119-.
[8]	LIU Wen-Qing. Finite Element Analysis of the Effect of Circles on Temperature Fields and Stress Fields of Flanges [J]. , 2012, 25(4): 41-.